Organix Building System

VASTHAF Waterproofing Chemicals

VASTHAF Waterproofing Chemicals

Business Type : Manufacturer, Exporter, Supplier

Product Details

Packaging Type Plastic Barrels, Drums Tanker
Packaging Size 0-5kg, 10-15 kg 15-20kg, 20-25kg and 50-100kg
Grade Technical Grade
Specific Gravity 1.38
Features Longer Shelf Life
Quality Superior
For More Information Click Here PDF View

Additional Information

Product Code WP07

Preferred Buyer From

Location United Arab Emirates

DRYTEX VASTAF PW9400 is a highly flexible elastomeric urethane resin based super elastic waterproofing and protection system designed for use in contact with potable water to waterproof water tanks and reservoirs in new construction and restoration. DRYTEX VASTAF PW9400 is a internal waterproofing lining of potable water reservoir and wastewater tanks, secondary containment structures where superior flexibility ,long lasting and resistance to fungus and chemicals is required (waste water treatment facilities). DRYTEX VASTAF PW400 is a fluid applied seamless waterproofing membrane, consisting of Component A and Component B.


  • UV resistant and Abrasion resistant
  • Crack resistant and Superior Flexibility
  • Superior freeze/thaw resistance and corrosion resistant
  • Excellent resistance to salt, acids, alkalis and other chemicals
  • Effective protection against acid rain
  • Self-curing and breathable
  • Continuous water immersion possible
  • Superior negative/positive waterproofing
  • Good for potable water and confirmed for use in drinking water environments (Confirmed to NSF/ANSI 61)
  • Bridges substrate crack up to 3 mm

The proper surface preparation is essential for a successful waterproofing. Remove all deteriorated and loose concrete, form release agents, oil, grease, laitance, dust, dirt and efflorescence by dry or wet sandblast, shot blast, or high-pressure water. Repair deeper areas using OBS recommended material. Reinforce and seal all joints, penetrations, cracks using SealFlex construction joint sealants.All bigger cracks must be treated using DRYTEX VASTAF PW9400 and reinforcing mat. Prefill any open cracks larger than 2 mm with DRYTEX VASTAF PW9400 or any other material recommended by OBS Embed a strip of reinforcing mat into the wet DRYTEX VASTAF PW9400 and apply a second coat to fully cover the reinforcing mat ( Consult OBS technical support to select the suitable reinforcement material according to the substrate).

Component Part A and Part B are separately packed and mixing suitable amount of these two components together on site and then stirred uniformly to have consistency which to be applied on the prepared substrate Pot life is 60 min @ 35 °C.

Can be applied conventionally by brush ,roller or spray equipment.. It is recommended to apply first coat by brush to obtain optimum adhesion. DRYTEX VASTAF PW400 Waterproofing Membrane has excellent high build properties, and can be built up to 2000 micron wet in one application. However from a curing point of view and dependant on weather conditions at the time of application, it is more pertinent to apply and build up the membrane in two or more coats, to allow quicker cure in each stage. The thicker the application the longer the cure.

0.8 litre of mixed membrane applied wet at 600 micron thick will cover 1 square etre. When bridging wider cracks, bed reinforcing mat into the first layer, allowing for over coating once cured. It is ideal for reinforcing cracks in concrete floors prior to tiling. For all round protection and durability, the final coat in the system should be applied at a rate of 0.8litre per square ,metre giving an optimum dry film thickness. The service life of the membrane is a direct correlation to final dry film thickness. A built in latent curing mechanism activated by loss happens in 3 stages. Firstly there is the initial evaporation of the majority of liquid in the system, followed by the second stage where the surface skins over and cures. The third stage (which takes a minimum of 2-6 days) is to complete cure and gain of cohesive strength. The application of the second coat can proceed after stage two. This is a two stage system, inclusive of the necessary bond breaker requirements being addressed.

Do not apply DRYTEX VASTAF PW9400 when the temperature is expected to be below 4°C within 48 hours, or when rain is imminent.

20 L ( Two Pack System )

Storage and transportation
DRYTEX VASTAF PW400, when stored on pallets in dry, cool area from moisture and direct sunlight, has a shelf life of 12 months. The liquid Component B must not freeze.Product information contained herein are presented in good faith and believed to be reliable. They do not constitute part of our terms and conditions of sale. It is also not a guarantee, either expressed or implied, that the data are correct or that products described are merchantable or fit for a particular purpose as methods of use are beyond our control. Customer should determine the suitability of our materials and installation recommendations before usage. Manufacturer's sole responsibility shall be to replace that portion of any product that proved to be defective


Yes! I am interested

Submit Your Requirement

Looking for "VASTHAF Waterproofing Chemicals" ?